Konica Minolta bizhub C3110 User Manual

Food, Drug and Cosmetic Act of 1990. Compliance is mandatory for La ser products marketed in the United

Konicaminolta bizhub c3110-u necə skan edə bilərəm

These results are ranked by popularity.

Error
13F0	Description: Engine control failure An undefined malfunction occurs in the engine section (PRCB, etc.).
0315	Description: PH board communication error • Mismatching of data being written and read occurs continuously for certain times during communication with the PH board. • The EEPROM of the PH board is not yet initialized.
D094	Description: Hard disk check disk error When the power switch ON, the hard disk fails to be checked.
13C5	Description: Imaging unit/M new article release. The status with the new unit is not cleared continuously for 3 times after the new imaging unit is set.
D3F3	Description: Write error of the counter area (SSD) An error occurs in the counter area when writing to the EEPROM.

Konica-Minolta Bizhub C3110 Common Errors

The most common error codes.

Error
13F0	Description: Engine control failure An undefined malfunction occurs in the engine section (PRCB, etc.).
0315	Description: PH board communication error • Mismatching of data being written and read occurs continuously for certain times during communication with the PH board. • The EEPROM of the PH board is not yet initialized.
D094	Description: Hard disk check disk error When the power switch ON, the hard disk fails to be checked.
13C5	Description: Imaging unit/M new article release. The status with the new unit is not cleared continuously for 3 times after the new imaging unit is set.
D3F3	Description: Write error of the counter area (SSD) An error occurs in the counter area when writing to the EEPROM.
13F0	Description: Engine control failure An undefined malfunction occurs in the engine section (PRCB, etc.).
0315	Description: PH board communication error • Mismatching of data being written and read occurs continuously for certain times during communication with the PH board. • The EEPROM of the PH board is not yet initialized.
D094	Description: Hard disk check disk error When the power switch ON, the hard disk fails to be checked.
13C5	Description: Imaging unit/M new article release. The status with the new unit is not cleared continuously for 3 times after the new imaging unit is set.
D3F3	Description: Write error of the counter area (SSD) An error occurs in the counter area when writing to the EEPROM.

Konica Minolta bizhub C3110 User Manual

timum utility of this device, all operators should care fully read and follow the instruct ions in this manual.

Please read the following section before connecting the machine to the supply. It contains important infor-

mation related to user safety and preventing equipment problems.
Please keep this manual in a handy place near the machine.

Make sure that you observ e all of the precautions that appear in different sections of this ma nual.

KM_Ver.08_OE
– Some parts of the contents of this section may not correspond with the purchased product.

Warning and precaution symbols

Be sure to observe th e safety precautions.

This manual contains the instructions that should be strict ly observed at all times to prevent injury to yourself

and other persons as well as damage to property.

Injuries and damage that might be caused by using the product improperl y are classified according to the

following symbols.

These are some of major exemplary graphical symbols

Power source connection

Pictorial indicat ion Description
WARNING Improper handling can ca use serious injury or death.
CAUTION Improper handling can cause mino r injury or damage to houses and
Descriptions Graphic
Descriptions Graphic
Descriptions
General prohibition Do no t disassemble Do not touch
General instruction Ground/Earth Unplug from outlet
General precaution High temperature Electrical shock
Use only the power cord supplied in the package. If a power cord is not
supplied, use only the power cord and plug that are specified in the user
documentation. Failure to use this cord could result in a fire or electrical
shock. If the power cord supplied in the package cannot be used in the
country where this product was sold , use a power cord that meets the
following conditions or contact your Technical Representative.
• The power cord has voltage and curr ent rating appropriate for the rat-
ing plate on this machine.
• The power cord meets regulatory requirements for the area.
• The power cord is provided with grounding pin/terminal.
Do not use the power cord to other produ cts. Failure to do that could re-
sult in a fire or electr ical shock.
1-6 bizhub C3110
Safety information
Do not scratch, abrade, place a heavy object on, heat, twis t, bend, step
on, pull on, or damage the power cord. Use of a damaged power cord
(exposed core wire, broken wire, etc.) could result in a fire or breakdown.
Should any of these conditions be found, immediately turn OFF the pow-
er switch, unplug the power cord from the power outlet, and then call
your authorized service representative.
Do not use the power source voltage other than being specified on the
machine. Failure to do that could result in a fire or electrical shock.
Do not use a multiple outlet adapter to connect any other a ppliances or
Use of a power outlet for more than the marked current value could result
in a fire or electrical shock.
Do not use an extension cord. Use of an extension cord could cause a
fire or electric shock. If the power cord furnished with the product is not
long enough to be plugged into a wall outlet, contact your Technical Rep-
resentative.
Do not unplug and plug in the power cord with a wet hand, as an electri-
cal shock could result.
Plug the power cord all the way into th e power outlet. Failure to do this
could result in a fire or electrical shock.
Make sure to ground this product. (Connect the power cord to an elec-
trical outlet that is equipped with a grounding terminal.) Failure to do so
and an unlikely event of leakage could result in a fire or electrical shock.
The outlet must be near the equipment and easily accessible. Otherwise
you can not pull out the power plug when an emergency occurs.
Do not place any objects around the power plug, as the power plug may
be difficult to pull out whe n an emergency occurs.
Do not tug the power cord when unplugging. Pulling on the power cord
could damage the cord, resulting in a fire or electrical shock.
Remove the power plug from the outl et more than one time a year and
clean the area between the plug terminals. Dust that accumulates be-
tween the plug termina ls may cause a fire.
bizhub C3110 1-7
1.2 Safety information

Installation

Keep this bag away from babies and children. Do not use in cribs, beds,
carriages, or playpens. The thin film may cling to nose and mouth and
prevent breathing. This bag is not a toy.
Do not place a flower vase or other co ntainer that contains water, or met-
al clips or other small metallic object s on this product. Spilled water or
metallic objects dropped inside the produ ct could result in a fire, electri-
cal shock, or breakdown.
Should a piece of metal, water, or any other sim ilar foreign matter get in-
side the product, immediately turn OFF the power switch, unplug the
power cord from the power outlet, an d then call your Technical Repre-
sentative or your authorized service representative.
Make sure that the powe r cord is placed on a si te in which no person
would step on or trip over it. Stepping on or tripping over the power cord
could heat the power cord, resultin g in a fire or electric shock.
When the product has been installed, fix the product using the fixing legs.
Not using the fixing legs could cause the product to move or topple over .
Do not place the product in a dusty pl ace, or a site exposed to soot or
steam, near a kitchen table, bath, or a humidif ier. A fire, electrical shock,
or breakdown could result.
Do not place this product on an unstable or tilte d bench, or in a location
subject to a lot of vibration and shock. It could drop or fall, causing per-
sonal injury or mechanical breakdown.
Do not let any object plug the ventilati on holes of this product. Heat could
accumulate inside the product, resulting in a fire or malfunction.
Whenever moving this product, be sure to disconnect the power cord
and other cables. Failure to do this could damage the cord or cable, re-
sulting in a fire, electrical shock, or breakdown.
When moving this product, always hold it at the locations specified in the
User’s Guide or other documents. If the unit is moved while held at loca-
tions other than those specified, it may fall, causing se vere personal in-
1-8 bizhub C3110
Safety information

Using the product

Do not modify this product, as a fi re, electrical shock, or breakdown
could result. If the produ ct employs a laser, the laser beam source could
cause blindness.
Do not attempt to remove the covers and panels which have bee n fixed
to the product. Some products have a high-voltage part or a laser beam
source inside that could cause an electrical shock or blindness.
Do not keep using this product, if th is product becomes inordinately hot
or emits smoke, or unusual odor or noise. Immediately turn OFF the pow-
er switch, unplug the power cord from the power outlet, and then call
your Technical Representative or your authorized service representative.
If you keep on using it as is, a fi re or electrical shock could result.
Do not keep using this product, if this product has been dropped or its
cover damaged. Immediately turn OFF the power switch, unplug the
power cord from the power outlet, and then call your Technical Repre-
sentative or your authorized service representative. If you keep on using
it as is, a fire or electrical shock could result.
Do not use flammable sprays, liquids, or gases inside or near this ma-
chine. Do not clean the inside of this machine using a flam mable gas
duster. A fire or ex plosion could result.

This machine generates a weak magnetic field. If you experience any un-
usual symptoms with your implanta ble medical equipment (cardiac
pacemaker, etc.) while near the machine, move away from the machine
and see a doctor immediately.
If you use an implantable medical equipment (cardia c pacemaker, etc.),
do not bring the IC card reader close from the implant within 12 cm at all
times. The radio waves may affect implantable medica l equipment (car-
diac pacemaker, etc.) operations.
Using this product in a poorly ventila ted room for a long time or produc-
ing a large volume of copies or prin ts may cause the odor of exhaust air
from the machine. Ventilate the room well.
The inside of this product has areas subject to high temperature, which
may cause burns.
When checking the inside of the un it for malfunctions such as a paper
misfeed, do not touch the locations (around the fusing unit, etc.) which
are indicated by a “Caution HOT” cau tion label. A burn could result.
Unplug the product when you will not use the product for long periods of
When using the machine, do not look at the light of th e lamp for a pro-
longed time. Eyestrain could result.
Do not use stapled paper, conductive paper (such as silver paper or car-
bon paper) or treated heat-sensitive/i nkjet paper, otherw ise a fire may re-
bizhub C3110 1-9
1.2 Safety information

Consumables

Do not throw toner or a container that contains toner (e.g., toner car-
tridge, PC drum unit, imaging unit, and developing unit) into an open
flame. The hot toner may scatter and cause burns or other damage.
Do not leave toner-related parts (e.g ., toner cartridge, PC drum unit, im-
aging unit, and developing unit) within easy reach of children. Licking any
of these parts or ingesting to ner could damage your health.
Do not store toner-related parts (e.g ., toner cartridge, PC drum unit, im-
aging unit, and developing unit) near devices susceptible to magnetism,
such as precision equipment and data storage devices, otherwise they
may malfunction. They could caus e these products to malfunction.
Do not force open the toner-related pa rts (e.g., toner ca rtridge, PC drum
unit, imaging unit, and developing unit ). If toner tumbles from the toner
bottle, take utmost care to avoid inha ling it or even getting skin contact.
If toner lands on your skin or clothing, wash thoroughly with soap and
If you inhale toner, move to a place with fresh ai r and gargle with a lot of
water repeatedly. Should you get symptoms such as coughing, seek
medical advice.
If you get toner into your eyes, immediately rinse them with running water
for over 15 minutes. Seek medical advice if irritation persists.
If you swallow toner, rinse out your mouth and drink a few glasses of wa-
ter. Seek medical ad vice if necessary.
Never touch the electrical contacts of the toner cartridge or the imaging
unit, as an electrostatic discharge may damage the product.
The fusing section is extremely hot. Before replacing the fusing unit, be
sure to open doors and covers of the machine. Then, leave the machine
to stand idle for a specified period of time and make sure that the fusing
sec ti on ha s c oo led do wn to ro om tem pe ra tu re . F ail ur e t o f ol lo w t hes e i n-
structions could result in a burn.
1-10 bizhub C3110
Regulation notices

1.3 Regulation notices

GS Certification

This product is GS-certified for the KONICA MINOLTA branded model bizhub C3110.
The equipment is not intended for use at a video workstation in compliance with BildscharbV.

CE Marking (Declaration of Conformity) for users of the European Union (EU)

This product complies with the following EU directives:
2004/108/EC, 2006/95/EC, 2009/125/EC
This declaration is valid for the areas of the European Union (EU) or EFTA only.
This device must be used with a shielded interface cable.

The use of non-shielded interface cables is likely to re sult in interference w ith radio communications and is

prohibited under 2004/108/EC rules.
USER INSTRUCTIONS FCC PART 15 – RADIO FREQUENCY DEVICES (for

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter-

ference in a residential installation. This equipment ge nerate s, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructi ons, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful in terference to radio or television re ception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation betwee n the equipment and receiver.

– Connect the equipment into an outlet on a circuit dif f erent from that to which the receiver is connected.

– Consult the dealer or an experien ced radio/TV technician for help.

– The design and production of this unit conform to FCC regulations, and any changes or modifications

must be registered with the FCC and are subject to FCC control. An y changes made by the purchaser
or user without first contacting the manufa cturer will be subject to penalty under FCC regulations.
– This device must be used with a shielded interface cable.

– The use of non-shielded cables is likely to result in interference wi th radio communications and is pro-

hibited under FCC rules.
FCC: Declaration of Conformity
Product Type Multi Function Peripherals
Product Name bizhub C3110
Options PF-P14, MK-P04, FK-512, HD-P06, AU-201
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions:
(1) This device may not caus e harmful interference, and

(2) this device must accept any interference received , includi ng interference that may cause undesired op-

bizhub C3110 1-11
1.3 Regulation notices
INTERFERENCE-CAUSING EQUIPMENT ST ANDARD (ICES-003 ISSUE 5) (for
Canada users)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device must be used with a shielded interface cable.

The use of non-shielded cables is likely to result in interference with radio co mmunications and is prohibited

under ICES-003.

Electromagnetic Interference

This product must be used with a sh ielded interface cable.

The use of non-shield cables is likely to result in in terference with radio commun ications and is prohibited

under CISPR 22 and local rules.

Laser Safety

This product employs a Class 3B laser diode having maximum power of 22 mW and wavelength of

This product is certified as a Class 1 laser product pe r IEC 60825-1: 2007. Sin ce the laser beam is concealed

by protective housings, the product does not emit hazardo us laser radiation as long as the product is oper-

ated according to the instructions in this manual.

Internal Laser Radiation

Maximum average radiation power: 13.6 μW at the laser aperture of the print head unit.
Wavelength: 770-800 nm
This product employs a Class 3B laser diod e that emits an invisible laser beam.
The laser diode and the scanning polygon mirr or are incorporated in the print head unit.
The print head unit is NOT A FIELD SERVICE ITEM:
Therefore, the print head unit should not be opened under any circumstances.
Laser Aperture of the Print Head Unit
1-12 bizhub C3110
Regulation notices

CDRH regulations

This machine is certified as a Class 1 Laser product under Radiation Performance Standard according to the

Food, Drug and Cosmetic Act of 1990. Compliance is mandatory for La ser products marketed in the United

States and is reported to the Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug

Administration of the U.S. Department of Health and Human Services (DHHS). This means that the device

does not produce hazardous laser radiation.

The label shown on page 1-13 indicate s compliance with the CDRH regulations and must be attached to la-

ser products marketed in the United States.
Use of controls, adjustments or pe rformance of procedures other than those specified in this manual
may result in hazardous radiation exposure.
– This is a semiconductor laser. The maximum power of the laser diode is 22 mW and the wavelength is

For European users

Use of controls, adjustments or pe rformance of procedures other than those specified in this manual
may result in hazardous radiation exposure.
– This is a semiconductor laser. The maximum power of the laser diode is 22 mW and the wavelength is

For Denmark users

7 ADVARSEL
Usynlig laserstråling ved åbning, når sikkerhedsafbrydere er ude af funktion. Undgå udsættelse for
stråling. Klasse 1 laser produkt der opfylder IEC60825 sikkerheds kravene.
– Dette er en halvlederlaser. Laserdiodens højeste styrke er 22 mW og bølgelængden er 770-800 nm.

For Finland, Sweden users

LOUKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
7 VAROITUS
Laitteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla ta valla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
– Tämä on puolijohdelaser. Laserdiodin sunrin teho on 22 mW ja aallonpituus on 770-800 nm.
Om apparaten används på annat sätt än i denna br uksanvisning specificerats, kan användaren utsät-
tas för osynlig laserstrålning, som överskrider gränsen för laser klass 1.

– Det här är en halvledarlaser. Den maximala effekten för laserdioden är 22 mW och våglängden ä r 770-

7 VAROITUS

– Avattaessa ja suojalukitus ohitetta essa olet alttiina näkymättömälle lasersäteilylle. Älä katso säteese en.

bizhub C3110 1-13
1.3 Regulation notices
– Osynlig laserstrålning när denna del är öppnad och spärren är urkopplad. Betrakta ej strålen

For Norway users

7 ADVARSEL!
Dersom apparatet brukes på annen måte enn spes ifisert i denne bruksanvisning, kan brukeren ut-
settes for unsynlig laserstråling som overskrider grensen for laser klass 1.
– Dette en halvleder laser. Maksimal effekt till la serdiode er 22 mW og bølgelengde er 770-800 nm.

Laser safety label

A laser safety label is attached to the outside of the machine, as shown below.

Ozone Release

During print operation, a small quanti ty of ozone is released. This amount is not large enough to harm anyone

adversely.However, be sure the room where the machine is being used has a dequate ventilation, especially

if you are printing a high volume of materials, or if th e machine is being used continuously over a long period.

Dégagement d’ozone

En cours de fonctionnement, l’impriman te ne dégage qu’une faible quanti té d’ozone, insuffisante pour provo-

quer un quelconque malaise personnel. Veillez cependant à ce que la pièce dans laquelle la machine est in-

stallée soit aérée de manière adéqua te, notamment si vous imprimez de gr os volumes ou si l’imprimante est

Konica Minolta bizhub c3110 Manual

Manual for Konica Minolta bizhub c3110 All in One Printer (7 pages)

Detail Specifications:
1020/1020672-bizhub_c3110.pdf file (29 Dec 2022)

• Manufacturer: Konica Minolta
• Category of Device: All in One Printer, Copier
• Document: bizhub c3110 Manual , File Type: PDF
• Updated: 29-12-2022
• Count of Pages: 7

Read Konica Minolta bizhub c3110 Manual Online

Accompanying Data:

Konica Minolta bizhub c3110 All in One Printer, Copier PDF Manual (Updated: Thursday 29th of December 2022 05:03:16 AM)

Rating: 4.9 (rated by 44 users)

Compatible devices: BIZHUB C280, C451, bizhub press c1070, 7216, bizhub pro C6500P, bizhub C220 Series, BIZHUB C252, DF-601.

• bizhub 750 Function manual (UPD: 23 Feb 2023, konica-minolta/bizhub-750.pdf) (view)
• bizhub C654e Shortcut manual (UPD: 26 Nov 2022, konica-minolta/bizhub-c654e.pdf) (view)
• C200 Operation & user’s manual (UPD: 09 Jan 2023, konica-minolta/c200.pdf) (view)
• bizhub C364e Using (UPD: 08 May 2023, konica-minolta/bizhub-c364e.pdf) (view)
• magicolor 4695MF Safety information manual (UPD: 10 Aug 2022, konica-minolta/magicolor-4695mf.pdf) (view)

Text Version of Manual

(Ocr-Read Summary of Contents, UPD: 29 December 2022)

• 1, A6DT-9231-00 konicaminolta.com 1 2 3 4 5 6 7 8 9 10 11 12 34.3 kg 75.6 lbs 13 14 15 16 17 17 18 19 20 21 22 23 Electrical Contacts 24 25 26 27 28 29 30 31 32 33 34 English 28 120 V: 220 V: 27 29 B 35 Required Space – Espace requis – Platzanforderungen – Ingombro – Requerimientos de espacio – Requisitos de espaço – Prostorové požadavky – Wymagania dotyczące …
• 2, A6DT-9231-00 konicaminolta.com 1 2 3 4 5 6 7 8 9 10 11 12 34.3 kg 75.6 lbs 13 14 15 16 17 17 18 19 20 21 22 23 Electrical Contacts 24 25 26 27 28 29 30 31 32 33 34 English 28 120 V: 220 V: 27 29 B 35 Required Space – Espace requis – Platzanforderungen – Ingombro – Requerimientos de espacio – Requisitos de espaço – Prostorové požadavky – Wymagania dotyczące wolnego miejsca – Helyig�…
• 3, Konica Minolta bizhub c3110 A6DT-9231-00 konicaminolta.com 1 2 3 4 5 6 7 8 9 10 11 12 34.3 kg 75.6 lbs 13 14 15 16 17 17 18 19 20 21 22 23 Electrical Contacts 24 25 26 27 28 29 30 31 32 33 34 English 28 120 V: 220 V: 27 29 B 35 Required Space – Espace requis – Platzanforderungen – Ingombro – Requerimientos de espacio – Requisitos de espaço – Prostorové požadavky – Wymagania dotyczące wolnego miejsca …
• 4, A6DT-9231-00 konicaminolta.com 1 2 3 4 5 6 7 8 9 10 11 12 34.3 kg 75.6 lbs 13 14 15 16 17 17 18 19 20 21 22 23 Electrical Contacts 24 25 26 27 28 29 30 31 32 33 34 English 28 120 V: 220 V: 27 29 B 35 Required Space – Espace requis – Platzanforderungen – Ingombro – Requerimientos de espacio – Requisitos de espaço – Prostorové požadavky – Wymagania dotyczące wolnego miejsca – Helyigény – Pr…
• 5, 35 36 37 38 Max. 250 sheets 80 g/m 2 (22 lb) 110 V – 127 V 8.8 A, 220 V – 240 V 4.5 A A Follow the instructions on the screen. Suivez les instructions à l’écran. Die Anweisungen auf dem Bildschirm befolgen. Seguire le istruzioni visualizzate sullo schermo. Siga las instrucciones que aparecen en pantalla. Siga as instruções na tela. Postupujte podle pokynů na obrazov…
• 6, Konica Minolta bizhub c3110 35 36 37 38 Max. 250 sheets 80 g/m 2 (22 lb) 110 V – 127 V 8.8 A, 220 V – 240 V 4.5 A A Follow the instructions on the screen. Suivez les instructions à l’écran. Die Anweisungen auf dem Bildschirm befolgen. Seguire le istruzioni visualizzate sullo schermo. Siga las instrucciones que aparecen en pantalla. Siga as instruções na tela. Postupujte podle p…
• 7, 35 36 37 38 Max. 250 sheets 80 g/m 2 (22 lb) 110 V – 127 V 8.8 A, 220 V – 240 V 4.5 A A Follow the instructions on the screen. Suivez les instructions à l’écran. Die Anweisungen auf dem Bildschirm befolgen. Seguire le istruzioni visualizzate sullo schermo. Siga las instrucciones que aparecen en pantalla. Siga as instruções na tela. Postupujte podle pokynů…